1RM.fit1RM.fit
Get Started Free
Exercise Library

Cable Rear Delt Row (Stirrups)

Cable Rear Delt Row (stirrups) is a beginner cable exercise for the primary: rear deltoids (shoulders) secondary: upper back (rhomboids, with the trapezius) assisting. Most lifters train it for 3 to 4 sets of 12 to 15 reps.

Stand facing a cable machine with stirrup handles attached at about chest height. Grasp the stirrups with a neutral grip and step back slightly. Keep your chest up and core braced. Pull the handles toward your upper chest by driving your elbows outward and squeezing your rear delts. Slowly extend your arms back to the starting position under control and repeat.

ShouldersCable
Cable Rear Delt Row (stirrups)
Primary muscle
Primary: Rear Deltoids (Shoulders) Secondary: Upper Back (Rhomboids
Secondary muscles
Trapezius)
Equipment
Cable
Difficulty
Beginner
Typical volume
3–4 sets × 12–15 reps
Category
Shoulders

How to Do the Cable Rear Delt Row (stirrups)

  1. Attach two stirrup handles to a single cable set at upper chest height and stand facing the stack.
  2. Grip one handle in each hand with palms facing down or each other, then step back until the weight lifts.
  3. Stand with feet shoulder width, knees soft, and arms extended toward the pulley.
  4. Pull both handles toward the upper chest while driving the elbows out wide at shoulder height.
  5. Let the hands separate as they near the chest and squeeze the rear delts and shoulder blades together.
  6. Return the handles slowly to full reach, letting the shoulder blades drift forward at the end.
  7. Keep the torso upright and still through every rep of the set.

Common Mistakes

  • Hands staying together: Keeping the handles close at the finish throws away the advantage of the stirrups. Spread the hands apart as the elbows pass the torso so the rear delts finish the rep.
  • Elbows dropping to the ribs: Low elbows turn the move into a lat row. Keep the upper arms level with the shoulders so the handles travel toward the collarbones.
  • Leaning back to move the stack: Using body weight to pull the handles takes tension off the rear delts. Brace the trunk and lower the weight until the body stays still.

Programming Tips

Use 3 to 4 sets of 12 to 15 reps at the end of a shoulder or pull session after pressing and heavier rows. It is an isolation movement for the rear delts and upper back, so it belongs in the accessory block where a hard squeeze matters more than the weight.

Set the pulley at upper chest height, hold one stirrup in each hand, and start with 10 to 20 kg on the stack. Add one plate once all sets reach 15 strict reps with a pause at the squeeze. The most common fault is the elbows dropping toward the ribs; fix it by picturing the elbows tracing a line at shoulder height from the pulley to behind the back.

Common Questions

What does the cable rear delt row with stirrups work?

It targets the rear deltoids with the rhomboids and middle trapezius squeezing the shoulder blades together. The separate handles allow a wider finish than a bar, which improves the rear delt contraction.

Are stirrup handles better than a rope for rear delt rows?

They are very similar, but the stirrups allow the hands to spread even wider than a rope and let you choose your grip angle. The rope is quicker to set up on most machines, so use whichever is available.

How much weight should I use for stirrup rear delt rows?

Most people get the best results with 10 to 25 kg on the stack. The rear delts are small and respond to strict reps with a pause, so a weight you can control through the full range beats a heavy swing.

Related shoulders exercises

Other ways to train the same muscle, with whatever equipment you have.

Cable Standing Face Pull
Cable
Cable Standing Face Pull With Rope
Cable
Cable Supine Reverse Fly
Cable
Machine Lateral Raise
Leverage Machine
Smith Machine Upright Row
Smith Machine
Band Pull Apart
Band

See every shoulders exercise →

Programming the Cable Rear Delt Row (stirrups)

Track This Exercise in the App

Log your cable rear delt row (stirrups) sets in 1RM.fit and watch your estimated 1RM update automatically as you get stronger.

Download on theApp StoreGET IT ONGoogle Play