1RM.fit1RM.fit
Get Started Free
Exercise Library

Machine Reverse Shoulder Press (Plate Loaded)

Lever Reverse Shoulder Press (plate Loaded) is an intermediate leverage machine exercise for the shoulders (deltoids), with the triceps and upper chest assisting. Most lifters train it for 3 to 4 sets of 8 to 12 reps.

This move, the Lever Reverse Shoulder Press (plate Loaded), is an overhead press variation using a lever machine. This overhead press changes the base or grip of a standard press to shift shoulder emphasis. It's often programmed early in a session while the shoulders are fresh.

ShouldersLeverage Machine
Lever Reverse Shoulder Press (plate Loaded)
Primary muscle
Shoulders (deltoids)
Secondary muscles
triceps, upper chest, trapezius
Equipment
Leverage Machine
Difficulty
Intermediate
Typical volume
3–4 sets × 8–12 reps
Category
Shoulders

How to Do the Lever Reverse Shoulder Press (plate Loaded)

  1. Load equal plates on each side and sit facing the back pad with your chest and stomach lightly against it.
  2. Adjust the seat so the handles start around shoulder height when you reach up and grip them.
  3. Grip the handles with palms facing forward or neutral, depending on the handle design, and set wrists over elbows.
  4. Brace your trunk and press the handles upward until your arms are nearly straight overhead.
  5. Keep your chest lightly on the pad and your head neutral rather than pushing it forward.
  6. Lower the handles slowly back to shoulder level, keeping tension in the shoulders before the next rep.

Common Mistakes

  • Leaning away from pad: Without a back rest, lifters often lean back and turn it into an incline press. Keep the torso tall and lightly in contact with the pad.
  • Shrugging the shoulders: Pushing the shoulders up to the ears shifts work to the traps and pinches the joint. Keep the neck long and press the handles, not the shoulders.
  • Partial range reps: Heavy plates tempt short reps near lockout. Lower until hands reach shoulder level on every rep and reduce load if you cannot.

Programming Tips

Use 3 to 4 sets of 8 to 12 reps early in a shoulder session while the delts are fresh, or as a second overhead press after a free weight press. The upright, reversed position limits back arching and makes it a good choice for strict hypertrophy work. It pairs well with lateral raises and rear delt work later in the session.

Set the seat so the handles start level with your shoulders and your torso stays upright. Start with roughly 10 to 20 kg of total plates, often less than you use facing forward, and add 2.5 kg once all sets reach 12 clean reps. Slow eccentrics of about three seconds increase difficulty without extra plates. The most common fault is leaning back to change the pressing angle; fix it by keeping the sternum on the pad for the full set.

Common Questions

Why sit backwards on a shoulder press machine?

Sitting backwards changes the pressing path to a more vertical line and removes the back rest you would arch against. Many lifters feel more shoulder and less chest this way.

What muscles does the reverse shoulder press work?

It works the front and side delts and the triceps, with the upper traps stabilizing. Upper chest involvement is lower than in a standard seated press.

Is the reverse machine shoulder press safe?

Yes, it is safe when the seat is set correctly and you keep the movement controlled. Anyone with shoulder impingement should stay in a pain-free range.

Know your Lever Reverse Shoulder Press (plate Loaded) 1RM →
Use the Overhead Press 1RM Calculator to estimate your one-rep max from a normal working set.

Related shoulders exercises

Other ways to train the same muscle, with whatever equipment you have.

Machine Seated Reverse Fly
Leverage Machine
Machine Seated Shoulder Press
Leverage Machine
Machine Shoulder Press (Plate Loaded)
Leverage Machine
Handstand Walk
Bodyweight
Kettlebell Sots Press
Kettlebell
Smith Machine Shoulder Press
Smith Machine

See every shoulders exercise →

Programming the Lever Reverse Shoulder Press (plate Loaded)

Track This Exercise in the App

Log your lever reverse shoulder press (plate loaded) sets in 1RM.fit and watch your estimated 1RM update automatically as you get stronger.

Download on theApp StoreGET IT ONGoogle Play